Roel holds the finished pulled Iberico pork with pieces of dark bark.

BBQ Airflow and Better Bark: An Iberico Pulled Pork Test

Roel Westra

A good rub deserves a good bark. In this cook, Roel uses an Iberico pork neck on the Napoleon Apollo 22 to explore what happens when smoke and air can move freely around the meat. The colour develops quickly, but the rising heat also shows why the water pan matters.

The takeaway: Roel builds the bark first, adds the water pan when the heat starts climbing, then wraps the pork once the outside has the colour he wants. Airflow is part of the result; managing the heat is just as important.

Iberico pork neck, Pork seasoning and Texas seasoning

The starting point is a pork neck with plenty of marbling. Roel chooses Iberico because he wants that fat running through the meat for pulled pork. He coats it with PitmasterX Pork Seasoning, then adds PitmasterX Texas seasoning for the structure of the bark.

The two rubs have different jobs in this cook: Pork provides the base seasoning, while Texas adds another layer to the outside. Roel sprinkles both directly onto the meat; he does not measure a fixed ratio.

Roel seasons an Iberico pork neck with PitmasterX Pork and Texas seasoning.
Pork Seasoning goes on first; Texas seasoning adds a second layer for the bark.

The Napoleon Apollo 22 setup

The Apollo 22 is a vertical charcoal smoker with stackable sections and a removable water pan. For this demonstration, Roel starts with the pan removed and the meat on the upper cooking grate, leaving open space between the briquettes and the pork.

He fills the charcoal area with briquettes and lights a small section in the centre. This is the Minion-style setup shown in the video: the fire spreads gradually into the surrounding fuel. A few wood chunks supply the smoke; the wood species is not identified.

Lighting a small fire in the centre of the Apollo 22 briquettes.
A small fire in the centre of the briquettes starts the Minion-style setup.

Roel keeps the top vent open. In this particular setup, he observes that air still enters through gaps even with the lower vents closed. That is an observation about this cook, rather than a vent setting to copy onto every smoker.

What happened during the cook?

After 1½ hours: fast bark development, rising heat

At the first check, the pork already has a deep mahogany colour and the bark is starting to set. Roel likes how quickly the outside is developing. The trade-off is that the smoker is getting hotter without the water pan.

This is the important turning point. He does not simply leave the pork exposed to an increasingly hot fire. Once the colour is where he wants it, he changes the setup.

Mahogany-coloured bark on the Iberico pork during the first check.
At the first check, the pork already shows a deep mahogany colour.

The water pan goes back in

Roel removes the upper section, installs the water pan and adds hot water before rebuilding the smoker. Keep water away from the hot coals when doing this: splashing water onto the fire can produce a sudden burst of steam.

In the video, the pan is used to bring the heat back under control and add moisture to the cooking environment. The top vent is opened again so smoke can continue to escape. The cook moves from building the surface quickly to finishing the meat with the pan in place.

Roel pours hot water into the reinstalled water pan of the Apollo 22.
Roel reinstalls the water pan during the cook to manage the rising heat.

At about 3½ hours: enough colour to wrap

Another two hours later, the bark is much darker, with the mahogany colour still visible underneath. Roel decides it is developed enough. Leaving the pork exposed for longer would keep changing the outside, so this is the point where he wraps it in aluminium foil.

He normally considers adding butter when wrapping some barbecue cuts. Here, he leaves it out: this Iberico neck already contains plenty of fat, and he wants to keep the focus on the pork. No butter or extra wrapping liquid is added in the video.

Dark bark on the Iberico pork neck before wrapping.
The darker bark before the pork is wrapped in foil.

After about 6 hours: pull the meat and mix in the bark

Roel takes the wrapped pork off the smoker, opens it in a tray and pulls it apart. The dark exterior breaks up through the tender meat. That contrast is the point of the whole cook: the bark brings the seasoned, smoky outside into every portion.

He pulls this piece shortly after unwrapping it. That describes what happened here; there is no separate resting stage shown in this cook.

Roel holds the finished pulled Iberico pork with pieces of dark bark.
The finished Iberico pork pulls apart, bringing the dark bark into the meat.
Observed timing in this video
Elapsed cooking time What Roel does
About 1½ hours Checks the bark and adds the water pan as the heat rises.
About 3½ hours Wraps the pork after the bark has darkened further.
About 6 hours Unwraps and pulls the finished pork.

These are the timings of this cook, not a fixed schedule for every pork neck. The video does not specify the meat weight, a measured rub quantity or a maintained cooking temperature.

What this airflow test tells us

The most useful lesson is to watch what the surface of the meat is doing and respond. In this cook, an open path around the pork produces the colour Roel wants quickly, but it also comes with rising heat. Adding the water pan and wrapping later are part of the method, not afterthoughts.

This is one demonstration, not a side-by-side trial with identical pork necks on different smokers. The rub, the exposed heat, the fat in the meat and the later wrapping all contribute to the result. It does not establish that higher airflow always makes better barbecue, or that a fuel-efficient cooker cannot build a good bark.

For a broader look at choosing when to wrap and what to do with the cooking juices, read Roel’s pulled pork guide.

Questions about the cook

Why use two seasonings?

Roel applies Pork Seasoning as the base and adds Texas seasoning specifically for the bark’s structure. Both are used before the meat goes on the smoker.

Why start without the water pan?

It lets Roel demonstrate the exposed cooking setup and early bark development. The pan goes back in when he sees that the heat needs controlling. Starting without it is part of this demonstration, not a requirement for every Apollo cook.

Why wrap once the bark is dark?

The exterior has reached the colour Roel wants. Wrapping changes the final stage of the cook so the pork can finish without remaining directly exposed in the same way.

Does every pulled pork cook take six hours?

No. Six hours is the approximate duration reported here. Use this video to understand Roel’s decisions, rather than treating its timeline as a promise for a different cut or setup.

Watch the complete airflow test

See the Apollo setup, the first bark check and the water-pan change in the original PitmasterX video.

Equipment and seasoning used

Pork and Texas seasoning are our own PitmasterX products. The cook also uses briquettes, wood chunks, a water pan, aluminium foil and a tray.

By Roel Westra, PitmasterX. Based on the PitmasterX cooking video originally published on 9 May 2026. The observations and timings above refer to the cook shown in that video.

Tillbaka till blogg