A sliced pork belly rib showing the meat, fat and crisp skin layers

Crispy-Skin Pork Belly Ribs on the Monolith Avantgarde

Roel Westra

Ribs, pork belly and crispy skin in one piece: that was the idea I took to my butcher. We kept the belly and skin attached to the ribs, then cooked the cut in three stages on the Monolith Avantgarde. First smoke, then tenderness, then a cast iron finish for the skin.

2 custom-cut racksSkin-on pork belly ribs
About 4 hoursTo tenderness, plus crisping and resting
94°C / 201°FCore temperature reached in this cook

Ask the butcher for the right cut

You need pork belly with the rib bones and skin still attached. Show your butcher the cut in the video: we trimmed the slabs, cut the ribs shorter and removed most of the cartilage. The result has ribs at the bottom, a generous layer of belly in the middle and skin on top.

That combination needs more than a standard rib routine. The meat has to soften, the belly fat has to render, and the skin needs a separate finish. In the video I cooked two racks; their exact weight was not given, so use tenderness and the thickness of your pieces to guide the cook.

Custom-cut pork belly with the rib bones and skin still attached
Keep the belly, rib bones and skin together for this custom cut.

Ingredients

  • 2 racks of skin-on pork belly ribs, custom-cut by your butcher, with most of the cartilage removed
  • PitmasterX Texas Seasoning, enough to coat all sides
  • A little rendered pork fat, reserved from the foil boats for the plancha finish

You will also need charcoal, beechwood smoking pellets, heavy-duty aluminium foil, heat deflectors, cooking grates and a cast iron plancha.

How to make crispy-skin pork belly ribs

  1. Set up the Monolith for indirect cooking.

    Light the charcoal, fit the heat deflectors and cooking grates, then stabilise the barbecue at 120°C / 248°F. Adjust the vents to suit your fire and conditions.

  2. Season all sides.

    Coat the pork belly ribs with PitmasterX Texas Seasoning. These thick pieces have several exposed surfaces, so cover the sides as well as the top and underside.

  3. Smoke until the colour develops.

    Place the ribs over indirect heat and add beechwood pellets through the Monolith’s smoke feed system. In this cook, I checked the colour after about 45 minutes, then increased the barbecue temperature to around 140°C / 284°F to develop the mahogany colour further. Move on when the outside has the colour you want.

    Roel putting seasoned pork belly ribs into the Monolith for indirect smoking
    Begin with indirect heat and beechwood smoke.
  4. Make foil boats and leave the skin uncovered.

    Form a snug foil boat around the underside and sides of each rack, keeping the skin exposed. The boat collects the rendered fat and juices while the uncovered skin can dry. Raise the cooking grates to increase the distance from the heat below, then return the ribs skin-side up.

    Pork belly ribs in a foil boat with the skin left uncovered
    Wrap the bottom and sides, while leaving the skin open to the heat.
  5. Cook until the meat is tender.

    Insert the thermometer into the thick meat, avoiding the bones. Open the vents a little further to increase the cooking heat and continue cooking indirectly. In the video, the ribs reached 94°C / 201°F after about four hours of cooking in total. Check that a probe slides into the meat with little resistance; the skin should also have softened before the crisping stage.

  6. Switch to a cast iron plancha.

    Lift the ribs off the barbecue. Using suitable heat protection, remove the cooking grates and heat deflectors and install the plancha. Open the foil boats and reserve a small amount of the rendered fat. The plancha gives the skin a cooking surface while keeping most of the dripping fat away from the open coals.

  7. Crisp the skin carefully.

    Add a little reserved fat to the plancha and place the ribs skin-side down. Let the surface heat up progressively and keep checking the skin. Remove the ribs as soon as the skin is crisp, rather than continuing to darken it. Remove any temperature probe that is not rated for this contact-heat stage before placing the meat on the plancha.

    Pork belly ribs on a cast iron plancha over the Monolith charcoal fire
    The plancha provides the final crisping stage after the meat has softened.
  8. Rest, slice and serve.

    Give the ribs a short rest, then slice between the bones. Serve pieces that include all three layers: rib meat, juicy belly and crisp skin. If finishing the racks one at a time, the first can rest while the second crisps.

The result, and what I would change next time

The meat was extremely juicy and tender, and the skin delivered the crunch I wanted. It was also darker than I would have liked. That is part of this experiment: the smoke colour on the skin became even darker during the cast iron finish.

Finished skin-on pork belly ribs on the cutting board
The finished rack: a dark exterior, tender belly and crisp skin.

Next time, I want to protect the skin from some of the smoke while still giving the meat plenty of flavour. For this version, the key is to keep watching the skin during the plancha stage. The meat is already tender; the last stage only needs to deliver the crunch.

Watch the complete recipe

Watch on YouTube

  1. 00:00 — The idea: ribs, belly and skin
  2. 00:48 — The custom butcher’s cut
  3. 01:19 — Monolith setup at 120°C
  4. 02:09 — Texas Seasoning
  5. 02:40 — Beechwood smoke
  6. 04:15 — Building colour at 140°C
  7. 05:07 — The foil boat method
  8. 06:27 — Four hours and the tenderness check
  9. 07:30 — Switching to the plancha
  10. 08:20 — Crisp skin, resting and slicing
  11. 09:24 — Tasting and what to improve

Equipment and seasoning

Made possible by Monolith. ChefsTemp is a PitmasterX partner. PitmasterX Texas Seasoning is our own product.

Roel Westra · PitmasterX
Based on the video published on 4 April 2026.

Vissza a blogba